Phoenix Contact TRIO-PS/1AC/5DC/10 TRIO-PS/1AC/5DC/10 Power Supply

Model number
TRIO-PS/1AC/5DC/10

Primary-switched TRIO POWER power supply for DIN rail mounting, input: 1-phase, output: 5 V DC/10 A

Price and availability on request

We reply by email or phone, Monday to Saturday, 10:30 am to 6:30 pm.

Several models? Add each to your enquiry list and send them as one enquiry.

Request a quote

Sent with the product details: Phoenix Contact TRIO-PS/1AC/5DC/10 TRIO-PS/1AC/5DC/10 Power Supply.

A phone number or an email address is needed, so we can reply.

We use these details only to reply to your enquiry. See our privacy notice.

Key features

  • Output 5 V DC ±1 %, 10 A (-25 °C ... 55 °C)
  • Input 100 V AC ... 240 V AC
  • Efficiency > 80 % (230 V AC)
  • Width 40 mm
  • Operating temperature -25 °C ... 70 °C (> 55° C derating - 2.5%/K)
  • Degree of protection IP20

Specifications

Input data
Nominal input voltage range100 V AC ... 240 V AC
Input voltage range85 V AC ... 264 V AC (Derating < 90 V AC - 2.5 %/K)
Derating< 90 V AC (2.5 %/V)
Input voltage range AC85 V AC ... 264 V AC (Derating < 90 V AC - 2.5 %/K)
Electric strength, max.300 V AC
Voltage type of supply voltageAC
Inrush current< 30 A
Inrush current integral (I2t)< 1.9 A2s
AC frequency range45 Hz ... 65 Hz
Mains buffering time> 40 ms (120 V AC); > 180 ms (230 V AC)
Current consumption1 A (120 V AC); 0.5 A (230 V AC)
Nominal power consumption131.4 VA
Protective circuitTransient surge protection; Varistor
Power factor0.48
Typical response time< 1 s
Permissible backup fuseB6 B10 B16
Recommended breaker for input protection6 A ... 16 A (Characteristics B, C, D, K)
Discharge current to PE< 3.5 mA
Output data
Efficiency> 80 % (230 V AC)
Output characteristicU/I
Nominal output voltage5 V DC ±1 %
Setting range of the output voltage (USet)4.5 V DC ... 6 V DC (> 12 V DC, constant capacity restricted)
Nominal output current (IN)10 A (-25 °C ... 55 °C)
Derating55 °C ... 70 °C (2.5 %/K)
Feedback voltage resistanceapprox. 9 V DC
Protection against overvoltage at the output (OVP)< 9 V DC
Max. capacitive loadunlimited
Active current limitationApprox. 12 A (in the event of a short-circuit)
Control deviation< 1 % (change in load, static 10 % ... 90 %); < 2 % (change in load, dynamic 10 % ... 90 %); < 0.1 % (change in input voltage ±10 %)
Residual ripple< 60 mVPP
Output power50 W
Peak switching voltages nominal load< 70 mVPP
Maximum no-load power dissipation1.5 W
Power loss nominal load max.13.5 W
Rise time< 2 ms (UOUT (10 % ... 90 %))
Connection in parallelyes, for redundancy and increased capacity
Connection in seriesyes
Connection data - Input
Connection methodScrew connection
Conductor cross-section, rigid min.0.2 mm²
Conductor cross-section, rigid max.2.5 mm²
Conductor cross-section flexible min.0.2 mm²
Conductor cross-section flexible max.2.5 mm²
Conductor cross-section AWG min.24
Conductor cross-section AWG max.14
Stripping length9 mm
Screw threadM2,5
Tightening torque, min0.4 Nm
Tightening torque max0.5 Nm
Connection data - Output
Connection methodScrew connection
Conductor cross-section, rigid min.0.2 mm²
Conductor cross-section, rigid max.2.5 mm²
Conductor cross-section flexible min.0.2 mm²
Conductor cross-section flexible max.2.5 mm²
Conductor cross-section AWG min.24
Conductor cross-section AWG max.14
Stripping length9 mm
Screw threadM2,5
Tightening torque, min0.4 Nm
Tightening torque max0.5 Nm
Signaling
Types of signalingLED
Signaling - Signal output
Status display"DC OK" LED green
Note on status displayUOUT < 0.9 x UN - LED flashing
Electrical properties
Insulation voltage input/output4 kV AC (type test); 2 kV AC (routine test)
Insulation voltage output / PE500 V DC (routine test)
Insulation voltage input / PE2 kV AC (type test); 2 kV AC (routine test)
Product properties
Product typePower supply
Product familyTRIO POWER
MTBF (IEC 61709, SN 29500)> 500000 h
Product properties - Insulation characteristics
Protection classI
Overvoltage categoryIII
Degree of pollution2
Dimensions
Width40 mm
Height130 mm
Depth115 mm
Dimensions - Installation dimensions
Installation distance right/left0 mm / 0 mm
Installation distance top/bottom50 mm / 50 mm
Mounting
Mounting typeDIN rail mounting
Assembly notealignable - horizontally 0 mm, vertically 50 mm
Mounting positionhorizontal DIN rail NS 35, EN 60715
With protective coatingno
Material specifications
Housing materialMetal
Type of housingSteel sheet, zinc-plated
Side element versionAluminum
Environmental and real-life conditions - Ambient conditions
Degree of protectionIP20
Ambient temperature (operation)-25 °C ... 70 °C (> 55° C derating - 2.5%/K)
Ambient temperature (storage/transport)-40 °C ... 85 °C
Climatic class3K3 (in acc. with EN 60721)
Max. permissible relative humidity (operation)≤ 95 % (at 25 °C, non-condensing)
Shock15g in all directions in acc. with IEC 60068-2-27
Vibration (operation)< 15 Hz, amplitude ±2.5 mm (according to IEC 60068-2-6); 15 Hz ... 150 Hz, 2.3g, 90 min.
Standards and regulations
Rail applicationsEN 50121-4
Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installationsEN 50178/VDE 0160 (PELV)
Standard – Limitation of mains harmonic currentsEN 61000-3-2
Standard - Electrical safetyEN 60950-1/VDE 0805 (SELV); EN 61558-2-17
Standard – Protection against shock currents, basic requirements for protective separation in electrical equipmentEN 50178
Standard – Safety extra-low voltageEN 60950-1 (SELV); EN 60204 (PELV)
Standard - Safe isolationDIN VDE 0100-410
Standard - Safety of transformersEN 61558-2-17
Approvals
UL approvalsUL/C-UL listed UL 508; UL/C-UL Recognized UL 60950-1
Approvals - Conformity/Approvals
SIL in accordance with IEC 615080

Specifications are from the manufacturer's published information. Confirm critical values with us or the datasheet before ordering. Brand names, logos and model names are trademarks of their respective owners, used only to identify the product. Details

Model numbers in this series (1)

Send us the complete code you need and we will quote it.

  • 2902646

About the TRIO-PS/1AC/5DC/10

TRIO POWER power supply for DIN-rail mounting with standard functionality. Primary-switched TRIO POWER power supply for DIN rail mounting, input: 1-phase, output: 5 V DC/10 A Order no. 2902646.