Phoenix Contact STEP-PS/1AC/24DC/0.75/FL STEP-PS/1AC/24DC/0.75/FL Power Supply

Model number
STEP-PS/1AC/24DC/0.75/FL

Primary-switched STEP POWER power supply for DIN rail mounting, input: 1-phase, output: 24 V DC/0.75 A

Price and availability on request

We reply by email or phone, Monday to Saturday, 10:30 am to 6:30 pm.

Several models? Add each to your enquiry list and send them as one enquiry.

Request a quote

Sent with the product details: Phoenix Contact STEP-PS/1AC/24DC/0.75/FL STEP-PS/1AC/24DC/0.75/FL Power Supply.

A phone number or an email address is needed, so we can reply.

We use these details only to reply to your enquiry. See our privacy notice.

Key features

  • Output 24 V DC, 0.75 A (-25 °C ... 55 °C)
  • Input 100 V AC ... 240 V AC
  • Efficiency > 84 % (for 230 V AC and nominal values)
  • Width 36 mm
  • Operating temperature -25 °C ... 70 °C (> 55° C derating - 2.5%/K)
  • Degree of protection IP20

Specifications

Input data - AC operation
Nominal input voltage range100 V AC ... 240 V AC
Input voltage range85 V AC ... 264 V AC
Voltage type of supply voltageAC
Inrush current< 15 A (typical)
Inrush current integral (I2t)< 0.1 A2s
AC frequency range45 Hz ... 65 Hz
Frequency range DC0 Hz
Mains buffering timetyp. 15 ms (120 V AC); typ. 70 ms (230 V AC)
Current consumption0.3 A (120 V AC); 0.25 A (230 V AC)
Nominal power consumption36.9 VA
Protective circuitTransient surge protection; Varistor
Power factor0.58
Typical response time< 0.5 s
Input fuse1.25 A (slow-blow, internal)
Recommended breaker for input protection6 A ... 16 A (Characteristics B, C, D, K)
Input data - DC operation
Input voltage range95 V DC ... 250 V DC
Voltage type of supply voltageDC
Output data
Efficiency> 84 % (for 230 V AC and nominal values)
Output characteristicU/I
Nominal output voltage24 V DC
Output current Imax1.4 A
Nominal output current (IN)0.75 A (-25 °C ... 55 °C); 0.83 A (-25 °C ... 40 °C permanent)
Derating55 °C ... 70 °C (2.5 %/K)
Feedback voltage resistance≤ 35 V DC
Protection against overvoltage at the output (OVP)< 35 V DC
Control deviation< 1 % (change in load, static 10 % ... 90 %); < 2 % (change in load, dynamic 10 % ... 90 %); < 0.1 % (change in input voltage ±10 %)
Residual ripple< 75 mVPP (20 MHz)
Output power18 W
Peak switching voltages nominal load< 15 mVPP (20 MHz)
Maximum no-load power dissipation< 0.5 W
Power loss nominal load max.< 3.6 W
Rise time< 0.5 s (UOUT (10 % ... 90 %))
Connection in parallelyes, for redundancy and increased capacity
Connection in seriesyes
Fuse protection (secondary side)electronic
Connection data - Input
Connection methodScrew connection
Conductor cross-section, rigid min.0.2 mm²
Conductor cross-section, rigid max.2.5 mm²
Conductor cross-section flexible min.0.2 mm²
Conductor cross-section flexible max.2.5 mm²
Conductor cross-section AWG min.24
Conductor cross-section AWG max.12
Stripping length6.5 mm
Screw threadM3
Tightening torque, min0.5 Nm
Tightening torque max0.6 Nm
Connection data - Output
Connection methodScrew connection
Conductor cross-section, rigid min.0.2 mm²
Conductor cross-section, rigid max.2.5 mm²
Conductor cross-section flexible min.0.2 mm²
Conductor cross-section flexible max.2.5 mm²
Conductor cross-section AWG min.24
Conductor cross-section AWG max.12
Stripping length6.5 mm
Screw threadM3
Tightening torque, min0.5 Nm
Tightening torque max0.6 Nm
Signaling
Types of signalingLED
Operating voltage displayGreen LED
Signaling - Signal output - LED status indicator
Status display"DC OK" LED green
Note on status displayUOUT > 21.5 V - LED lights up
Electrical properties
Number of phases1
Insulation voltage input/output4 kV AC (type test); 3.75 kV AC (routine test); 3.75 kV AC (routine test); 4 kV AC (type test)
Product properties
Product typePower supply
Product familySTEP POWER
MTBF (IEC 61709, SN 29500)> 926000 h (40 °C)
Product properties - Insulation characteristics
Protection classII (in closed control cabinet)
Overvoltage categoryIII
Degree of pollution2
Dimensions
Width36 mm
Height90 mm
Depth Device depth (DIN rail mounting)37 mm (Device depth (DIN rail mounting))
Horizontal pitch2 HP
Dimensions - Installation dimensions
Installation distance right/left0 mm / 0 mm
Installation distance top/bottom30 mm / 30 mm
Mounting
Mounting typeDIN rail mounting
Assembly notealignable - 0 mm horizontally, 30 mm vertically
Mounting positionhorizontal DIN rail NS 35, EN 60715
With protective coatingno
Material specifications
Housing materialPlastic; PC
Foot latch materialPOM (Polyoxymethylene)
Environmental and real-life conditions - Ambient conditions
Degree of protectionIP20
Ambient temperature (operation)-25 °C ... 70 °C (> 55° C derating - 2.5%/K)
Ambient temperature (storage/transport)-40 °C ... 85 °C
Ambient temperature (start-up type tested)-40 °C
Climatic class3K3 (in acc. with EN 60721)
Max. permissible relative humidity (operation)≤ 95 % (at 25 °C, non-condensing)
Shock18 ms, 30g, in each space direction (according to IEC 60068-2-27)
Vibration (operation)< 15 Hz, amplitude ±2.5 mm (according to IEC 60068-2-6); 15 Hz ... 150 Hz, 2.3g, 90 min.
Temp codeT4 (70 °C)
Standards and regulations
Rail applicationsEN 50121-4
Budgetary standardIEC 60335-1
Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installationsEN 50178/VDE 0160 (PELV)
Standard – Limitation of mains harmonic currentsEN 61000-3-2
Standard - Electrical safetyIEC 62368-1 (SELV)
Standard - Approval for medical useIEC 60601-1, 2 x MOOP
Standard – Protection against shock currents, basic requirements for protective separation in electrical equipmentEN 50178
Standard – Safety extra-low voltageIEC 62368-1 (SELV) und EN 60204-1 (PELV)
Standard - Safe isolationDIN VDE 0100-410
Standard - Safety of transformersEN 61558-2-16
Approvals
CSACSA-C22.2 No. 107.1-01
UL approvalsUL/C-UL listed UL 508; UL/C-UL Recognized UL 60950-1; UL ANSI/ISA-12.12.01 Class I, Division 2, Groups A, B, C, D T4 (Hazardous Location); NEC Class 2 as per UL 1310
Approvals - Conformity/Approvals
SIL in accordance with IEC 615080

Specifications are from the manufacturer's published information. Confirm critical values with us or the datasheet before ordering. Brand names, logos and model names are trademarks of their respective owners, used only to identify the product. Details

Model numbers in this series (2)

Send us the complete code you need and we will quote it.

  • 2868622
  • STEP-PS/ 1AC/24DC/0.75/FL

About the STEP-PS/1AC/24DC/0.75/FL

STEP POWER primary-switched power supply for DIN-rail mounting, slim and compact, for distribution boards and building automation. Primary-switched STEP POWER power supply for DIN rail mounting, input: 1-phase, output: 24 V DC/0.75 A Order no. 2868622.