54, Ezra Street , Kolkata - 700001 , West Bengal, IndiaMonday to Saturday, 10:30 am to 6:30 pm

Industrial Supply Syndicate Kolkata, since 1977 Send an enquiry
Proton 3P ACPM AC Power Monitor, Three Phase

Proton 3P ACPM AC Power Monitor, Three Phase

Brand
Proton
Model number
3P ACPM

Meter for measuring and showing electrical parameters (Proton 3P ACPM).

Price and availability on request

Request a quote

Sent with the product details: Proton 3P ACPM AC Power Monitor, Three Phase.

A phone number or an email address is needed, so we can reply.

We use these details only to reply to your enquiry. See our privacy notice.

Key features

  • Fully Programmable
  • Complete protection for all unhealthy condition
  • All Set points programmable from keypad
  • Password Protection for controller
  • Different password for each menu set points
  • LCD Display (2X16 Char) with Back Light
  • Good stability, high reliability, and good quality of load
  • Simple 4 keys keypad for on side programming
  • Separate contact for DG
  • Direct display of Line voltage & actual current drawn by load
  • CT Ratio Settable
  • All faults Auto reset
  • D.G. Sensing
  • Fault log History.(last 10Faults)
  • All Menus are Password Protected
  • The AC Power Monitor is a solid state Power Meter
  • Monitoring of single phase AC supply including all types of energies. The AC Power Monitor is based on Microchip, with a high degree of programmability
  • The Meter has been programmed to operate as an intelligent front end measuring and storing device qualifies model AC Power Meter
  • The Meter’s supplied preprogrammed for operation and can be directly installed

Specifications

Specifications
Nominal Voltage Input1] Standard Voltage offered 415 V 3Ph AC(R,Y,B,N) Power supply 2] Accuracy Range: 50 – 115 % of nominal voltage. 3] Burden : < 2.5 VA per phase. 4] Overload: 1.2x nominal continuous
Nominal Input Current5 Amp 1] Accuracy Range for 5 Amps = 120 % nominal. 2] Burden < 0.5 VA per phase. 3] Overload 4.0x nominal continuous 4] Starting current 0.2% of nominal current.
Frequency50 Hz / 60 Hz range (±5 Hz)
Measured Parameters1] RMS Voltage (Volt) (R, Y, B Phase) Phase – Neutral measured. 2] RMS Current (Amps) (R, Y, B Phase) Phase current 3] Frequency (R, Y, B Phase) 4] Power Factor (R, Y, B Phase) 5] Active Power (KVA) (R, Y, B Phase) 6] Apparent Power (KW) (R, Y, B Phase) 7] Main’s KWH 8] DG KWH 9] DG Run hour 10] Mains Run hour
Protection1] Over Voltage Protection (Settable) 2] Under Voltage Protection (Settable) 3] Over Load Protection (Settable) 4] Under Load Protection (Settable) 5] Unbalance voltage/current (Settable) 6] Over Frequency (settable) 7] Over Frequency (settable) 8] Total KW Protection. (Settable) 9] Phase failure protection. (Settable)
Auxiliary PowerNo External power is required (Draws power from the voltage signal Inputs)
Accuracy1] Volt 0.25% ± 1 dgts. 2] Current 0.25% ± 1 dgts. 3] Frequency 0.1% Hz ± 1 dgts. 4] Power Factor 0.25% ± 1 dgts. (for 0.5 Lag – 1.0 - 0.8 Lead) 5] Active Power 0.5% ± 1 dgts. 6] Apparent Power 0.25% ± 1 dgts. 7] Active Energy Class 1.0
Communication Output1] Serial port : RS 485 2] Baud rate : Selectable 1200, 2400, 4800, 9600, 19200. (Default: 9600) 3] Unit No : 1-32 (Default 1) 4] Start bit : 1 5] Stop bit : 1 6] Protocol : MODBUS - RTU
Environmental1] Working Temp : 0 to 55º C 2] Storage Temp : 10 to 70º C 3] Relative humidity : 0 – 95 % non-condensive 4] Warm up time : 30 Sec
Enclosure1] Mounting : Panel mounting. 2] Position : Panel. 3] Enclosure : 96 X 96 X 110 mm. 4] Terminal : Screw ON Terminals.

Specifications are from the manufacturer's published information. Confirm critical values with us or the datasheet before ordering.

Related products