54, Ezra Street , Kolkata - 700001 , West Bengal, IndiaMonday to Saturday, 10:30 am to 6:30 pm

Industrial Supply Syndicate Kolkata, since 1977 Send an enquiry
Proton 1P ACPM AC Power Monitor, Single Phase

Proton 1P ACPM AC Power Monitor, Single Phase

Brand
Proton
Model number
1P ACPM

Meter for measuring and showing electrical parameters (Proton 1P ACPM).

Price and availability on request

Request a quote

Sent with the product details: Proton 1P ACPM AC Power Monitor, Single Phase.

A phone number or an email address is needed, so we can reply.

We use these details only to reply to your enquiry. See our privacy notice.

Key features

  • CT Ratio/Gain Configurable
  • All Menus are Password Protected
  • Different Passwords for each menu set points
  • 16 x 2 Line LCD display with Bakelite on controller front panel
  • Simple 4 Key keypad for on site programming
  • Automatic display of AC Voltages, Current parameters one by one in Run Mode
  • Separate contact for DG
  • Direct display of Line voltage & actual current drawn by Load
  • Run hours for Total Main KWH, Total DG KWH
  • D.G. sensing
  • Communication with PC given, separate contact for communication TX & RX
  • The AC Power Monitor is a solid state Power Meter
  • Monitoring of single phase AC supply including all types of energies. The AC Power Monitor is based on Microchip, with a high degree of programmability
  • The Meter has been programmed to operate as an intelligent front end measuring and storing device & serial port connectivity qualifies model AC Power Meter
  • The Meter’s supplied preprogrammed for operation and can be directly installed. The Meter can be read manually or through a RS-485 MODBUS RTU Protocol.(Optional)

Specifications

Specifications
Nominal Voltage Input-: 1] Standard Voltage offered Single Phase 230 V AC Power supply 2] Accuracy Range : 50 – 115 % of nominal voltage. 3] Burden < 2.5 VA per phase. 4] Overload 1.2x nominal continuous
Nominal Input Current5 Amp 1] Accuracy Range: For 5 Amps = 120 % nominal. 2] Burden: < 0.5 VA per phase. 3] Overload: 4.0x nominal continuous 4] Starting current: 0.2% of nominal current.
Terminals1) separate contact for DG. 2) Separate communication terminal.
Frequency50 Hz / 60 Hz range (±5 Hz).
Measured Parameters1] RMS Voltage (Volt) Phase – Neutral measured. 2] RMS Current (Amps) Phase current. 3] Frequency. 4] Power Factor. 5] Active Power (KVA). 6] Apparent Power (KW). 7] Main’s KWH. 8] DG KWH. 9] DG Run hour. 10] Mains Run hour.
Auxiliary PowerNo External power is required (Draws power from the voltage signal
Accuracy1] Volt: 0.25% ± 1 dgts. 2] Current : 0.25% ± 1 dgts. 3] Frequency: 0.1% Hz ± 1 dgts. 4] Power Factor: 0.25% ± 1 dgts. (For 0.5 Lag – 1.0 - 0.8 Lead) 5] Active Power: 0.5% rdg ± 1 dgts. 6] Apparent Power: 0.25% rdg ± 1 dgts. 7] Active Energy: Class 1.0
Communication Output1] Serial port : RS 485 2] Baud rate : Configurable 1200, 2400, 4800, 9600, 19200. (Default: 9600) 3] Unit No : Configurable 1-32 (Default 17) 4] Start bit : 1 5] Stop bit : 1 6] Protocol : MODBUS - RTU
Environmental1] Working Temp : 0 to 55º C 2] Storage Temp : 10 to 70º C 3] Relative humidity : 0 – 95 % non-condensive 4] Warm up time : 30 Sec
Enclosure1] Mounting : Panel mounting. 2] Position : Panel. 3] Enclosure : 96 X 96 X 110 mm. 4] Terminal : Screw ON Terminals.
KeySET : This key is used to change the controller from RUN mode to FUNCTION mode for parameter setting ENTER: To save the new parameter value INC : Up scroll the parameter & parameter value. DEC : Down scroll the parameter & parameter value.
NoteTo Load default parameter Press INC key On power ON.
Options
Optional featuresMODBUS RS-485 RTU protocol connectivity.; GSM Communication to know working status of unit Runflow and fault if any.; Customised sprm can be offerd.

Specifications are from the manufacturer's published information. Confirm critical values with us or the datasheet before ordering.

Related products