Kusam Meco KM-DSO-2D10 100 MHz Digital Storage Oscilloscope with Waveform Generator
- Brand
- Kusam Meco
- Model number
- KM-DSO-2D10
2-channel 100 MHz digital storage oscilloscope, 1 GSa/s, 7-inch display, serial bus triggers (UART, LIN, CAN, SPI, IIC), FFT, with a built-in 25 MHz arbitrary waveform generator.
Price and availability on request
Downloads
- Datasheet: Kusam Meco KM-DSO-2D10 PDF, 117 KB
Key features
- Oscilloscope and arbitrary waveform generator in one
- Serial bus triggering
- FFT and maths
- Save waveforms as CSV and screens as BMP
Specifications
| Bandwidth | 100 MHz |
|---|---|
| Channels | 2 analog channels |
| Time base | 2 ns/div – 100 s/div (1-2-5 sequence) |
| Vertical range | 2 mV/div – 10 V/div |
| Rise time | ≤ 3.5 ns typical |
| Low frequency response (−3 dB) | ≤ 10 Hz |
| Sample rate | 1 GSa/s (single channel); 500 MSa/s (two channels); equivalent 50 GSa/s |
| Acquisition modes | Normal, peak, average, high resolution |
| Input | DC, AC, GND coupling; 1 MΩ ±2%, 20 pF ±3 pF; 300 V CAT II; max. 300 V rms (10X) |
| Channel isolation | > 40 dB; delay < 500 ps |
| Triggers | Edge, pulse, video (NTSC, PAL), slope, overtime, pattern, interval, under-amplitude, UART, LIN, CAN, SPI, IIC |
| Maths | +, −, ×, ÷, FFT |
| Storage | CSV file, BMP picture (24 bit) to external memory |
| Channels | 1 |
|---|---|
| Waveforms | Sine, square, ramp, exponential, noise, DC, arbitrary |
| Frequency | Sine 0.1 Hz – 25 MHz; square 0.1 Hz – 10 MHz; ramp 0.1 Hz – 1 MHz; exponential 0.1 Hz – 5 MHz; arbitrary 1 µHz – 25 MHz |
| Square duty | 1% – 99% |
| Ramp symmetry | 0% – 100% |
| Noise bandwidth | > 25 MHz |
| Amplitude | 5 mV – 3.5 Vpp (50 Ω); 10 mV – 7 Vpp (high impedance) |
| DC offset | 1.75 V (50 Ω), 3.5 V (high impedance) |
| Arbitrary wave length | 4096 |
| Waveform depth | 4 KSa |
| Burst | N cycle (1 – 1024), infinite |
| Output impedance | 50 Ω, high impedance |
| Display | 7-inch TFT, 800 × 480; point or vector; adjustable brightness; persistence 1 s – infinite |
|---|---|
| Interface | USB host, USB device |
| Power consumption | < 15 W |
| Power supply | 100 – 120 V AC rms (±10%), 45 – 440 Hz; 120 – 240 V AC rms (±10%), 45 – 66 Hz; CAT II |
| Weight | Approx. 1900 g |
| Accessories | Passive probe (1.5 m, 10:1), test leads, power cord, USB cable, CD with software and user manual, carrying case |
Specifications are from the manufacturer's published information. Confirm critical values with us or the datasheet before ordering.
Related products
-
Enquire about Kusam Meco KM 20-10
Kusam Meco KM 20-10 20 MHz Analog Oscilloscope
Dual-trace 20 MHz analog oscilloscope with 6-inch CRT, 1 mV/div sensitivity, X-Y mode, TV sync separation and ≤ 17.5 ns rise time; mains powered.
-
Enquire about Kusam Meco KM 2001
Kusam Meco KM 2001 Digital Signal Generator, 0.2 Hz to 2 MHz
Sine and square wave signal generator, 0.2 Hz – 2 MHz in 6 ranges with digital frequency display, 600 Ω output, attenuator in 20 dB steps to 60 dB; mains powered.
-
Enquire about Kusam Meco KM 2002
Kusam Meco KM 2002 Digital Function Generator, 2 MHz
Function generator to 2 MHz: sine, square, rectangle, sawtooth, triangle and pulse, duty cycle 20 – 80%, 5-digit frequency and 3-digit amplitude LED displays, 50 Ω output.
-
Enquire about Kusam Meco KM 2005
Kusam Meco KM 2005 Digital Function Generator, 5 MHz
Function generator, 0.1 Hz – 5 MHz: sine, triangle, square, ±pulse and sawtooth, 20 Vp-p into no load, TTL / CMOS output, VCF input and built-in 1 Hz – 20 MHz frequency counter.
